Does not detect disks during installation - LSI Logic controller
Does not detect disks during installation - LSI Logic controller
Hi,
today I bought an HP Z600 computer which I will devote to the server. The computer has a RAID controller LSI Logic model SAS3041E-HP.
Why does the installation program not see my disks connected to this controller? Do I need additional software? This is my first controller and I thought that installing CentOS 8 would detect my disks
___________________________________________________
EDIT:
___________________________________________________
The CentOS 7 installation program has detected the controller and disks
today I bought an HP Z600 computer which I will devote to the server. The computer has a RAID controller LSI Logic model SAS3041E-HP.
Why does the installation program not see my disks connected to this controller? Do I need additional software? This is my first controller and I thought that installing CentOS 8 would detect my disks
___________________________________________________
EDIT:
___________________________________________________
The CentOS 7 installation program has detected the controller and disks
Re: Does not detect disks during installation - LSI Logic controller
Sounds like it'll be one of the controllers that Red Hat decided not to support in RHEL 8. The RHEL Release Notes have a list.
The future appears to be RHEL or Debian. I think I'm going Debian.
Info for USB installs on http://wiki.centos.org/HowTos/InstallFromUSBkey
CentOS 5 and 6 are deadest, do not use them.
Use the FAQ Luke
Info for USB installs on http://wiki.centos.org/HowTos/InstallFromUSBkey
CentOS 5 and 6 are deadest, do not use them.
Use the FAQ Luke
Re: Does not detect disks during installation - LSI Logic controller
Can I create a pendrive with the system installation and add drivers to this controller to the pendrive with install?
Re: Does not detect disks during installation - LSI Logic controller
See the "Known issues" section of the CentOS 8 Release Notes that starts with "Support for some adapters has been removed.." You need to find out the vendor:device ID pairing of your controller and file a request for a DUD with ELRepo.
CentOS Forum FAQ
Re: Does not detect disks during installation - LSI Logic controller
My controller is 1c: 00.0 SCSI storage controller [0100]: Broadcom / LSI SAS1064ET PCI-Express Fusion-MPT SAS [1000: 0056] (rev 08)
and I didn't find it on this list, but I found SAS1064R on this list.
This computer is to be a KVM server and I want to install on it CentOS8 as a host system. There is no point in installing CentOS7 as a host?
As guest systems, I will also install CentOS8. Maybe one guest system will have CentOS7 installed.
and I didn't find it on this list, but I found SAS1064R on this list.
This computer is to be a KVM server and I want to install on it CentOS8 as a host system. There is no point in installing CentOS7 as a host?
As guest systems, I will also install CentOS8. Maybe one guest system will have CentOS7 installed.
Re: Does not detect disks during installation - LSI Logic controller
Unless I'm mistaken, device [1000: 0056] is indeed supported by the mptsas driver in the CentOS-8 GA kernel (4.18.0-80). So not sure why it is not detected.
In any event you may want to try using the DUD image from ELRepo to install CentOS-8.
https://elrepo.org/linux/dud/el8/x86_64 ... elrepo.iso
In any event you may want to try using the DUD image from ELRepo to install CentOS-8.
https://elrepo.org/linux/dud/el8/x86_64 ... elrepo.iso
CentOS Forum FAQ
Re: Does not detect disks during installation - LSI Logic controller
You may also need to setup the disks in the controller.
I don't know about this work station, but normally you enter the
raid card setup during boot with CRTL plus a key combination.
I don't know about this work station, but normally you enter the
raid card setup during boot with CRTL plus a key combination.
Re: Does not detect disks during installation - LSI Logic controller
I have this DUD image on the second flash drive.
Normally boot from a USB stick with CentOS8 installation? Later I connect a second flash drive? I have never used such solutions
___________________________________
EDIT:
___________________________________
Ok, I know how to use it. The installer has detected disks connected to the controller.
Today I will carry out the installation and see if everything works properly
Normally boot from a USB stick with CentOS8 installation? Later I connect a second flash drive? I have never used such solutions
___________________________________
EDIT:
___________________________________
Ok, I know how to use it. The installer has detected disks connected to the controller.
Today I will carry out the installation and see if everything works properly