I'm upgrading my HP ML10 v2 Proliant server from a 4x1Gb NIC, to a 2x10Gb NIC. I use the server as an all-purpose home server, e.g. Unifi Controller, NAS, Plex, File Server (Samba), TimeMachine (Netatalk), VPN, some KVM VMs, etc, etc.
The current HP NC365T aggregated 4-port 1Gbps is well supported, and I got it to work easily when I switched to CentOS 8 (from 7) recently in a bonded setup.
The new HP NC523SFP 2-port 10Gbps SFP+ seems a bit harder to get to work on my CentOS 8 install? Did I even read that the standard driver for it may have been deprecated?
I run CentOS 8.1.1 and kernel 4.18.0-147.5.1.el8_1.x86_64.
Code: Select all
Linux hpnas 4.18.0-147.5.1.el8_1.x86_64 #1 SMP Wed Feb 5 02:00:39 UTC 2020 x86_64 x86_64 x86_64 GNU/Linux
Code: Select all
03:00.0 Ethernet controller: Broadcom Inc. and subsidiaries NetXtreme BCM5720 2-port Gigabit Ethernet PCIe
03:00.1 Ethernet controller: Broadcom Inc. and subsidiaries NetXtreme BCM5720 2-port Gigabit Ethernet PCIe
04:00.0 Ethernet controller: QLogic Corp. cLOM8214 1/10GbE Controller (rev 54)
04:00.1 Ethernet controller: QLogic Corp. cLOM8214 1/10GbE Controller (rev 54)
0a:00.0 Ethernet controller: Intel Corporation 82580 Gigabit Network Connection (rev 01)
0a:00.1 Ethernet controller: Intel Corporation 82580 Gigabit Network Connection (rev 01)
0a:00.2 Ethernet controller: Intel Corporation 82580 Gigabit Network Connection (rev 01)
0a:00.3 Ethernet controller: Intel Corporation 82580 Gigabit Network Connection (rev 01)
Code: Select all
br0: connected to br0
"br0"
bridge, xx:xx:xx:xx:xx:xx, sw, mtu 1500
ip4 default
inet4 192.nn.nn.nn/24
route4 192.nn.nn.nn/24
route4 0.0.0.0/0
inet6 nnnn::nnnn:nnnn:nnnn:nnnn/64
route6 nnnn::/64
route6 nnnn::/8
bond0: connected to bond0
"bond0"
bond, xx:xx:xx:xx:xx:xx, sw, mtu 1500
master br0
ens2f0: connected to ens2f0
"Intel 82580"
ethernet (igb), xx:xx:xx:xx:xx:xx, hw, mtu 1500
master bond0
ens2f1: connected to ens2f1
"Intel 82580"
ethernet (igb), xx:xx:xx:xx:xx:xx, hw, mtu 1500
master bond0
ens2f2: connected to ens2f2
"Intel 82580"
ethernet (igb), xx:xx:xx:xx:xx:xx, hw, mtu 1500
master bond0
ens2f3: connected to ens2f3
"Intel 82580"
ethernet (igb), xx:xx:xx:xx:xx:xx, hw, mtu 1500
master bond0
eno1: disconnected
"Broadcom NetXtreme BCM5720"
ethernet (tg3), xx:xx:xx:xx:xx:xx, hw, mtu 1500
eno2: disconnected
"Broadcom NetXtreme BCM5720"
ethernet (tg3), xx:xx:xx:xx:xx:xx, hw, mtu 1500
lo: unmanaged
"lo"
loopback (unknown), 00:00:00:00:00:00, sw, mtu 65536
DNS configuration:
servers: 192.nn.nn.nn
interface: br0
Thx