New Install No Ethernet
-
- Posts: 1
- Joined: 2020/12/12 01:36:47
New Install No Ethernet
New install of CentOS-7 minimal install on new computer. Went well, but no Ethernet. tried nmtui to set up network. No Ethernet device listed. Good light on switch, blinking yellow light on computer. Tried 'ip a' and it only shows the loopback. Tried lspci and got "command not found".
So, how do I get networking working on CentOS-7?
Thanks,
Michael
So, how do I get networking working on CentOS-7?
Thanks,
Michael
Re: New Install No Ethernet
Start with lspci -nn | grep -i net to get the PCI vendor/device ids and then check with grep -i $vendor /lib/modules/$(uname -r)/modules.* | grep -i $deviceid (substitute using your vendor/device ids before you run that) to see if there is a module that supports it already in the supplied kernel. Probably not since it would be listed if there was. If not then you probably want to check the ELRepo yum repo and see if they offer a kmod package that supports your card.
The future appears to be RHEL or Debian. I think I'm going Debian.
Info for USB installs on http://wiki.centos.org/HowTos/InstallFromUSBkey
CentOS 5 and 6 are deadest, do not use them.
Use the FAQ Luke
Info for USB installs on http://wiki.centos.org/HowTos/InstallFromUSBkey
CentOS 5 and 6 are deadest, do not use them.
Use the FAQ Luke
Re: New Install No Ethernet
Same Problem - I have a relatively new Dell laptop, and ifconfig does not list any adapters. I followed what you said Trevor and matched the device:id and have --
I checked online ElRepo for a match here : http://elrepo.org/tiki/DeviceIDs
There are no matches for "8086:0d4c" . Should I just move to CentOS 8?
Code: Select all
00:1f.6 0200: 8086:0d4c
There are no matches for "8086:0d4c" . Should I just move to CentOS 8?
Re: New Install No Ethernet
That adapter is supported on CentOS 8 but that only lives for the rest of this year. I think that if you download and manually install kmod-e1000e from elrepo that should support it. Make sure you also install their elrepo-release package so you get future updates.
The future appears to be RHEL or Debian. I think I'm going Debian.
Info for USB installs on http://wiki.centos.org/HowTos/InstallFromUSBkey
CentOS 5 and 6 are deadest, do not use them.
Use the FAQ Luke
Info for USB installs on http://wiki.centos.org/HowTos/InstallFromUSBkey
CentOS 5 and 6 are deadest, do not use them.
Use the FAQ Luke
Re: New Install No Ethernet
The error i'm getting while installing the kmod rpm is
Am downloading the latest cent 7 dvd iso hopefully will resolve, or I could download those 20-25 kernel rpms manually?failed dependencies : kernel >= 3.10.0-1127.19.1.el7 is needed by kmod-e1000e-3.8.4-3.el7_9.elrepo.x86_64
Re: New Install No Ethernet
What's the current output from rpm -q kernel ?
The future appears to be RHEL or Debian. I think I'm going Debian.
Info for USB installs on http://wiki.centos.org/HowTos/InstallFromUSBkey
CentOS 5 and 6 are deadest, do not use them.
Use the FAQ Luke
Info for USB installs on http://wiki.centos.org/HowTos/InstallFromUSBkey
CentOS 5 and 6 are deadest, do not use them.
Use the FAQ Luke
Re: New Install No Ethernet
kernel-3.10.0.1127.el7.x86_64
Maybe my sudo password is wrong
Maybe my sudo password is wrong
Re: New Install No Ethernet
No, you've installed an old version of CentOS 7 (7.8) not the latest 7.9. The kmod you downloaded is for 7.9 so you have two choices, either update the system to 7.9 using a 3.10.0-1160* series kernel so that the kmod you have already downloaded works or download the older kmod-e1000e which is
kmod-e1000e.x86_64 3.8.4-2.el7_8.elrepo elrepo
That's http://elrepo.org/linux/elrepo/el7/x86_ ... x86_64.rpm
Once you have a network connection, make sure that you have elrepo-release installed and the elrepo repo enabled and then run yum update to get to the current versions of everything.
kmod-e1000e.x86_64 3.8.4-2.el7_8.elrepo elrepo
That's http://elrepo.org/linux/elrepo/el7/x86_ ... x86_64.rpm
Once you have a network connection, make sure that you have elrepo-release installed and the elrepo repo enabled and then run yum update to get to the current versions of everything.
The future appears to be RHEL or Debian. I think I'm going Debian.
Info for USB installs on http://wiki.centos.org/HowTos/InstallFromUSBkey
CentOS 5 and 6 are deadest, do not use them.
Use the FAQ Luke
Info for USB installs on http://wiki.centos.org/HowTos/InstallFromUSBkey
CentOS 5 and 6 are deadest, do not use them.
Use the FAQ Luke
Re: New Install No Ethernet
Yeah I tried the 7.8 kmod, same error, there is one more older one to try, Gonna download latest kernel and go with 7.9, these updates come quick, thank you