10 TB hdd not recognised

General support questions
User avatar
TrevorH
Site Admin
Posts: 33202
Joined: 2009/09/24 10:40:56
Location: Brighton, UK

Re: 10 TB hdd not recognised

Post by TrevorH » 2019/11/25 14:07:22

No, see above.
The future appears to be RHEL or Debian. I think I'm going Debian.
Info for USB installs on http://wiki.centos.org/HowTos/InstallFromUSBkey
CentOS 5 and 6 are deadest, do not use them.
Use the FAQ Luke

Blisk
Posts: 316
Joined: 2011/07/04 14:49:51
Contact:

Re: 10 TB hdd not recognised

Post by Blisk » 2019/11/26 07:54:31

Is it possible to run kernel higher than 3.1 on centos 7?

User avatar
TrevorH
Site Admin
Posts: 33202
Joined: 2009/09/24 10:40:56
Location: Brighton, UK

Re: 10 TB hdd not recognised

Post by TrevorH » 2019/11/26 07:59:33

Yes. We already ship 3.10 and 3.10 is 9 versions higher than 3.1.

It's "10" not "1" or "2" and 10 is larger than 1 or 2.
The future appears to be RHEL or Debian. I think I'm going Debian.
Info for USB installs on http://wiki.centos.org/HowTos/InstallFromUSBkey
CentOS 5 and 6 are deadest, do not use them.
Use the FAQ Luke

Blisk
Posts: 316
Joined: 2011/07/04 14:49:51
Contact:

Re: 10 TB hdd not recognised

Post by Blisk » 2019/11/26 08:08:14

oh yes sorry I see. than controller should work, but still can't recognise disks.

Blisk
Posts: 316
Joined: 2011/07/04 14:49:51
Contact:

Re: 10 TB hdd not recognised

Post by Blisk » 2019/11/27 09:20:19

I have changed controller, it is also Delock but another controller and now it works.

Blisk
Posts: 316
Joined: 2011/07/04 14:49:51
Contact:

Re: 10 TB hdd not recognised

Post by Blisk » 2019/11/30 08:23:57

I found out what was a problem.
It was a power cable for disks I tried all power cables from PSU and didn't worked after that I use splitter 4 power pin to two sata power connector and now works like it should.

desertcat
Posts: 843
Joined: 2014/08/07 02:17:29
Location: Tucson, AZ

Re: 10 TB hdd not recognised

Post by desertcat » 2019/11/30 19:00:31

Blisk wrote:
2019/11/30 08:23:57
I found out what was a problem.
It was a power cable for disks I tried all power cables from PSU and didn't worked after that I use splitter 4 power pin to two sata power connector and now works like it should.
Splitters cause problems. Sometimes -- many times -- the problem is simply the splitter has not been pushed in tight enough and there is a poor connection made; other times it is simply a faulty splitter, which can be fixed f you roll up your sleeves. That is usually true for Molex connectors, OTOH if it is SATA ->SATA connector I simply toss it, unless only one branch of the Y is dead and all I need is an extension, in that case I simply tape off the BAD end so I know not to use it. It is usually a good idea to buy a few extra extensions / Y's at the time you buy the first... just in case, that you you don't waste a lot of time. It is usually a quick way to troubleshoot a power problem -- if it only happens with one extension /Y but not another you know where the problem lies; OTOH if it is a repeatable problem then the problem probably lies in the PSU. (Been there; Done that).

Blisk
Posts: 316
Joined: 2011/07/04 14:49:51
Contact:

Re: 10 TB hdd not recognised

Post by Blisk » 2019/12/01 07:59:25

this time splitter solve a problem because all sata power connectors from PSU didn't work.

User avatar
TrevorH
Site Admin
Posts: 33202
Joined: 2009/09/24 10:40:56
Location: Brighton, UK

Re: 10 TB hdd not recognised

Post by TrevorH » 2019/12/01 12:38:39

If I am reding your post right, did you have to effectively use 2 separate power connectors from the PSU and feed them both into a splitter in reverse so that both were powering the drive at the same time? If so then I suspect your PSU is junk.
The future appears to be RHEL or Debian. I think I'm going Debian.
Info for USB installs on http://wiki.centos.org/HowTos/InstallFromUSBkey
CentOS 5 and 6 are deadest, do not use them.
Use the FAQ Luke

Blisk
Posts: 316
Joined: 2011/07/04 14:49:51
Contact:

Re: 10 TB hdd not recognised

Post by Blisk » 2019/12/01 17:07:59

TrevorH wrote:
2019/12/01 12:38:39
If I am reding your post right, did you have to effectively use 2 separate power connectors from the PSU and feed them both into a splitter in reverse so that both were powering the drive at the same time? If so then I suspect your PSU is junk.
No I didn't, I use the same cable from PSU for both disks and I have the same now with splitter

Post Reply